What is AMISTAR used for?
AMISTAR is a fungicide for the control of a wide range of diseases in Barley, Grapes, Maize, Onions, Peas, Potatoes, Ryegrass seed crops, Sweetcorn, field Tomatoes and Wheat.
Is AMISTAR fungicide systemic?
AMISTAR contains azoxystrobin, a broad spectrum fungicide from the strobilurin group. It has systemic, translaminar and protectant properties.
How do you use AMISTAR Top?
AMISTAR TOP may be applied by ground or aerial application equipment in potatoes. Aerial application may be used only for Early Blight (Target Spot) control. Apply in a sufficient volume of water to achieve thorough coverage of all foliage.
What is azoxystrobin used for?
Azoxystrobin is the ISO common name for an organic compound that is used as a fungicide. It is a broad spectrum systemic active ingredient widely used in agriculture to protect crops from fungal diseases.
How do you mix AMISTAR?
- Mixing and spraying. Half fill the sprayer with water, shake container, add AMISTAR then top up the tank whilst maintaining agitation. Apply using a medium quality spray. A spray pressure of at least 2 bar is preferred.
- Water volume. Refer to label.
- Rainfastness. 2 hours.
Is Dithane M 45 systemic fungicide?
Dithane is non-systemic fungicide with multi-site, protective action on contact.
What is Amistar Top fungicide?
Amistar Top is a broad spectrum and long duration control fungicide which covers a broad range of diseases like yellow rust, powdery mildew, late blight, sheath blight, downey mildew , leaf spots, grey mildews, red rot etc… in crops like Rice, Cotton, Sugarcane & Vegetables.
Does azoxystrobin need to be watered in?
After the application of Azoxystrobin-based fungicide products to target areas, you should water in the product after application. Most products provide preventative and curative control of labeled plant diseases for up to 4 weeks so expect to reapply once a month for continued protection and control.
How do you mix Amistar 50 WG?
Fill tank 50 to 75% full then start agitation. Slowly pour granules into tank and maintain agitation throughout spraying. DO NOT pre-mix AMISTAR WG granules. Dilute spraying: Use a sprayer designed to apply high volumes of water up to the point of run-off and matched to the crop being sprayed.
What is the price of Nativo?
Nativo Bayer Fungicide, Packet, 100g,250g And 1kg, Rs 6900/kg | ID: 22269516712.
In which disease apply Dithane M45 used for better management?
DITHANE M45 FUNGICIDE It is a broad-spectrum fungicide and is registered for the control of many fungal diseases (blight, leaf spot, rust, downy mildew, scab, leaf blight, anthracnose) in the field crops, fruits and vegetables etc.
How do you mix Dithane M45?
When applied by hand sprayers, 1 pound Dithane M45 per 100 gallons per acre is equivalent to 1 level tablespoon per gallon spray solution. Observe all directions for use, crops/sites, use rates, dilution ratios, precautions, and limitations which appear on the tank mix product label.
When can I mow after applying fungicide?
Answer: With most products like Prime Source Propiconazole 14.3 Select Fungicide, you will want to not mow your yard 2 days prior to application or 2 days after application to ensure it is fully absorbed into the yard and to see the full results. 11 of 12 people found this answer helpful.
How long does it take for fungicide to work on lawn?
Starts working within 24 hours to control common lawn diseases. Controls lawn diseases for up to 4 weeks.
How does switch fungicide work?
It inhibits spore germination and growth of germ tubes and mycelia on the plant surface, interfering with the fungal cell’s ability to properly regulate osmotic pressure, causing the cell to burst from excessive intracellular pressure and it blocks protein-kinase.
What is switch fungicide?
SWITCH is a combination of two fungicides for the control of Botrytis in Grapes, Bulb Onions, Botrytis, Anthracnose and Rhizopus in Strawberries and Botrytis and Anthracnose in Blueberries.